Yes, for smaller quantities than what's included with the 4 pack of the 9" SnapPad Jack Pads # SP54FR4 you can use the part # SP54FR, which is just for a single pad.
There isn't a 2-pack available but you can just order two of # SP54FR to get exactly what you're needing. view full answer...
The bolt does not come with the Replacement Foot Plate for Lippert Power Gear Hydraulic Jack # LC359344.
I checked with Lippert, and while there isn't an OEM replacement bolt, they did say that the correct bolt was a Grade 8 3/4"-16 x 1-1/2 bolt.
I have added a link below to a video review for you to check out as well of the Lippert Power Gear Hydraulic Jack # LC359344. view full answer...
The Andersen Wheel Chock and Leveler are sold separately from the Jack.
Part # AM3604 includes the leveler and chock and part # AM3620 includes the jack and a rubber grip. view full answer...
The Replacement Left Rear Leg for Lippert Components Ground Control 3.0 Electric Leveling System, # LC305339, will include the bracket needed to mount to the frame of a trailer. The leg will replace the current leg on a Lipper Ground Control 3.0 System.
The jack leg will include a new foot pad, but hardware and snapper pin for foot pad are not included. view full answer...
The Lippert 5th Wheel RV Landing Gear Foot Pad # LC314667 referenced in your question includes 2 foot pads. The listed price on the product page is for both pads together. view full answer...
The Replacement Return Spring Kit for Power Gear External Spring RV Leveling Jacks # LC359434 is the 500094 spring that you are looking for. The 500094 is an alternate part number for the Replacement Return Spring Kit for Power Gear External Spring RV Leveling Jacks # LC359434. If you are asking if we sell only the spring and not the whole kit, the answer is that the 500094 spring is only available in the kit. view full answer...
They do indeed. If you'll look at the provided diagram, you'll see that they cushion the interior housing, providing some give in case the shroud is hit by overhead limbs or other small obstructions while backing the RV. view full answer...
Yes, the Lippert Scissor Stabilizer Jacks # LC285326 is a set of two jacks with a 24 inch lift, maximum load capacity of 10,000 lbs (5,000 lbs per jack). The jacks have a collapsed height of 4-1/4 inches and extended height of 24 inches, providing a total of 24" of lift.
Note: This jack set is designed to stabilize a portion of your trailer's weight, not to support the full GVWR of your trailer. Do not use these jacks to lift your trailer or RV. Doing so will exceed the capacity of the... view full answer...
Both of our part numbers # SP54FR4 and # SP84FR represent the same XTRA size/style SnapPad in a quantity of 4. Either part number would work for your RV. view full answer...
The Lippert High-Speed Power Stabilizer Jack # LC369774 includes the following parts.
1- Stabilizer Jack Assembly
1- White Switch Housing # LC134025
1- Power Switch # LC144214
1- 6 Amp Auto Reset Breaker # LC134181
4- 3/8" Hex Head Mounting Bolts
4- 3/8" Hex Nuts
The following replacement parts are also available for the Stabilizer Jack Assembly
- Replacement Electric Stabilizer Jack Support Arm # LC1134122
- Replacement Electric RV Stabilizer Jack Motor # LC352338
- Replacement Foot... view full answer...
Yes, you would want to purchase 2 of the MORryde Scissor Jack Cross Brace Stabilizer for Trailers and RVs # MR82AR if you're wanting to install on both sets of stabilizers on your 2021 Grand Design Imagine. view full answer...
The Stackers Leveling Blocks for Trailers and RVs - 1-3/8" x 8-1/8" - Qty 4 # A10-0916 weigh approximately 4 lbs or just under 1 lb each. I've attached a couple review videos of this product to assist. view full answer...
The Epicord RV Power Cord, # 277-000154 and the Mighty Cord # A10-5036ENDBK are similar products from different manufacturers. Both have similar specs of being rated 50 amps, 125/250 V and 36' length. view full answer...
The Stromberg Carlson RV Bunk Ladder # LA-466 that you referenced is silver with black pads on each rung.
This ladder stands 5-1/2 feet tall and can be trimmed down shorter if needed. This would work well in your 2013 Jayco X213. view full answer...
I spoke with my contact at Therma Heat and they informed me that the thermostat of the # 277-000164 that you referenced uses a bi-metal contact. view full answer...
Brackets are not included with the Landing Gear Set w/ Handle # RVLG-8HDL. If you need them you can use the Replacement Weld-On 5th Wheel Landing Gear Leg Bracket for Lippert RVs # LC113511. You will need two for each leg so a total of four. view full answer...
If you're talking about a space to sit between the mounting brackets of the Ultra-Fab Power Twin II Manual Stabilizer # UF39-941704 and the frame of the trailer then no, this stabilizer does not have spacers. If you're trying to gain more clearance you could have a welder add in a spacer to the frame with some metal tubing but would need to ensure that tube is rated high enough to handle the pressure of the jack pushing against it. You could then use some self-tapping bolts with some Loctite... view full answer...